After a few years of lots of printing, including both my wedding and my brother’s wedding invitations, I’m finally now needing to refill the tanks. The printer works like a champion, and it’s so nice to not have to worry about filling up the cartridges. Over the past few years, I’ve printed countless shipping labels, photos, and other various documents. I was able to prime the cartridges, and then all was well again. It’s really just some suction syringes that you need to do this, and sells them. As soon as we unplugged the vents, it worked great! Instantly, my pictures were again vibrant.Ī few months ago, I had a similar issue, and I must have done something wrong, but I had to re-prime the cartridges, which involves sucking ink via the cartridge through the tubes. The water stays in the straw, just as my ink was staying in the hoses. If the airflow is blocked, picture someone holding their thumb over a straw and pulling it out of a soft drink. If you don’t, the airflow will be blocked. There are some air vents on the top of each ink cartridge, and you need to unplug the stopper at the top of each tank. In this picture, the vents are properly opened. I spoke with a really helpful person who showed me exactly what to check, and in the end, we found the issue, and it was MY fault. They told me to give them a call during business hours. I was frustrated, and I sent a note to the company. So… how did it work? It worked great at first, but after some time, I noticed that the colors were fading and eventually it seemed that the ink was so faint that it barely showed up. I got an “error” on my printer that Non-HP cartridges were installed. Once installed, it was time to give it a go! I followed the instructions to run a print head cleaning and printed out a few test pages. This is a great solution as it keeps the tank secure to the side of the printer, but it’s easy enough to pop it off if you need to move it around to refill the cartridges or do some other maintenance. This kit includes a set of plastic hooks with double sided tape so you can fasten it to the side of the printer. Locked and LoadedĪfter they’re installed properly, some other pieces are included to guide the hose so there it doesn’t get caught on anything as the print head moves back and forth. You place them all in the slots in a group, and then you snap them all in individually. As these units are all attached to the same ribbon of hoses. I installed it into my printer, which is only slightly more complicated than installing a standard set of ink cartridges. I received my replacement unit promptly, and after a quick visual inspection, the new cartridge unit looked good to go. That’s pretty solid customer service right there. They asked me to send a picture, and as soon as they got the picture, they sent me a brand new unit with a pre-paid label to return the defective unit. Uh oh…Ĭan you see the detached hose on the left? Bummmmmer… I received a defective unit. That’s where I hit my first snag… I pulled out the block of replacement ink cartridges I was supposed to install, and my hands got full of ink. Step one in installing a custom ink system is to remove the old cartridges. Furthermore, not only was the CIS cheaper, but we also got to keep the system once we were done printing invitations.Īnyhow, that was years ago, and the system worked well, but eventually it ran out of ink, and rather than refill it, I saw that had a new version out so I decided to spring for it. I justified the cost of a continuous ink system, $129.99 at the time of purchase, by comparing it against the hundreds of dollars we would have to pay a professional printer. We could either pay a printer a per-invitation fee or we could use our own printer. I have always been infatuated with the idea of continuous ink systems, but it wasn’t until we had to print wedding invitations a few years ago that we felt really needed one. What if, instead of having a bunch of small ink cartridges, you had external tanks of ink that had more ink than you’d ever need with hoses going to the print-head? That’s exactly a continuous ink system is. Is there any way out of the “razor and razor blade” model? Continuous ink systems can theoretically provide a solution. The darn things seem to run out of ink all the time, and it’s tough to buy one color at a time. We all hate having to buy new ink cartridges for our inkjet printers.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |